Download presentation

1
Transformers

2
**Transformer It is a static device.**

It transfers electrical energy from one electrical circuit to other with desired change in voltage and current, without changing the frequency(f=50Hz) and power. Constant flux device Magnetically coupled and electrically isolated Electro magnetic conversion device.

3
**Principle of operation**

It is based on principle of MUTUAL INDUCTION. According to which an e.m.f. is induced in a coil when current in the neighbouring coil changes.

6
**Constructional detail : Shell type**

Parallel magnetic circuit Windings are wrapped around the central limb of a laminated core. Sandwitch winding to reduce the leakage flux Less amount of copper & more amount of insulation is required

7
**Constructional detail : Core type**

Series magnetic circuit Windings are wrapped around two sides of a laminated square core. More amount of copper & less amount of insulation is required. Economical for high voltage applications

8
**Sectional view of transformers**

Note: High voltage conductors are smaller cross section conductors than the low voltage coils

9
**Core type Fig1: Coil and laminations of core type transformer**

Fig2: Various types of cores

10
**Fig: Sandwich windings**

Shell type The HV and LV windings are split into no. of sections Where HV winding lies between two LV windings In sandwich coils leakage can be controlled Fig: Sandwich windings

11
**Cut view of transformer**

12
**Transformer with conservator and breather**

13
**Working of a transformer**

1. When current in the primary coil changes being alternating in nature, a changing magnetic field is produced 2. This changing magnetic field gets associated with the secondary through the soft iron core 3. Hence magnetic flux linked with the secondary coil changes. 4. Which induces e.m.f. in the secondary.

15
**Ideal Transformers Zero leakage flux:**

-Fluxes produced by the primary and secondary currents are confined within the core The windings have no resistance: - Induced voltages equal applied voltages The core has infinite permeability - Reluctance of the core is zero - Negligible current is required to establish magnetic flux Loss-less magnetic core - No hysteresis or eddy currents

16
**Ideal transformer V1 – supply voltage ; I1- noload input current ;**

V2- output voltgae; I2- output current Im- magnetising current; E1-self induced emf ; E2- mutually induced emf

17
**Phasor diagram: Transformer on No-load**

18
**Transformer on load assuming no voltage drop in the winding**

Fig shows the Phasor diagram of a transformer on load by assuming No voltage drop in the winding Equal no. of primary and secondary turns

19
**Transformer on load Fig. a: Ideal transformer on load**

Fig. b: Main flux and leakage flux in a transformer

20
**Equivalent circuit of a transformer**

No load equivalent circuit:

21
**Equivalent circuit parameters referred to primary and secondary sides respectively**

22
**Transferring secondary parameters to primary side**

Cu loss after transfer = cu loss before transfer Where R21 - Equivalent secondary resistance w.r.t primary R01 = R1 + R21 Where R01 – Total primary resistance referred to secondary

23
**Equivalent circuit referred to primary side :**

24
**Transferring primary parameters to secondary side :**

Cu loss after transfer = cu loss before transfer = k2 R1 Where R11 - Equivalent primary resistance w.r.t secondary R02 = R2 + R11 Where R01 – Total secondary resistance referred to primary

25
**Equivalent circuit referred to secondary side :**

26
**Equivalent circuit w.r.t primary :**

where

27
**Approximate equivalent circuit**

Since the no load current is 1% of the full load current, the no load circuit can be neglected

28
Transformer Tests The performance of a transformer can be calculated on the basis of equivalent circuit The four main parameters of equivalent circuit are: - R01 as referred to primary (or secondary R02) - the equivalent leakage reactance X01 as referred to primary (or secondary X02) - Magnetising susceptance B0 ( or reactance X0) - core loss conductance G0 (or resistance R0) The above constants can be easily determined by two tests - Oper circuit test (O.C test / No load test) - Short circuit test (S.C test/Impedance test) These tests are economical and convenient - these tests furnish the result without actually loading the transformer Electrical Machines

29
Open-circuit Test In Open Circuit Test the transformer’s secondary winding is open-circuited, and its primary winding is connected to a full-rated line voltage. Usually conducted on H.V side To find (i) No load loss or core loss (ii) No load current Io which is helpful in finding Go(or Ro ) and Bo (or Xo )

30
Short-circuit Test In Short Circuit Test the secondary terminals are short circuited, and the primary terminals are connected to a fairly low-voltage source The input voltage is adjusted until the current in the short circuited windings is equal to its rated value. The input voltage, current and power is measured. Usually conducted on L.V side To find (i) Full load copper loss – to pre determine the efficiency (ii) Z01 or Z02; X01 or X02; R01 or R02 - to predetermine the voltage regulation

31
**Voltage regulation of a transformer**

recall Secondary voltage on no-load V2 is a secondary terminal voltage on full load Substitute we have

32
**Formula: voltage regulation**

33
**Transformer Efficiency**

Transformer efficiency is defined as (applies to motors, generators and transformers): Types of losses incurred in a transformer: Copper I2R losses Hysteresis losses Eddy current losses Therefore, for a transformer, efficiency may be calculated using the following: Electrical Machines

34
**Losses in a transformer**

Core or Iron loss: Total cu losses = = =

35
**Condition for maximum efficiency :**

36
**All day efficiency : The load at which the two losses are equal =**

All day efficiency is always less than the commercial efficiency

Similar presentations

© 2021 SlidePlayer.com Inc.

All rights reserved.

To make this website work, we log user data and share it with processors. To use this website, you must agree to our Privacy Policy, including cookie policy.

Ads by Google